Language
中国
韩国
韩国
韩国
韩国
韩国

东莞市金叠电子有限公司

Products

CAN bus termination resistor D-sub 9 pin male female connector
CAN bus termination resistor D-sub 9 pin male female connector
CAN bus termination resistor D-sub 9 pin male female connector
CAN bus termination resistor D-sub 9 pin male female connector
CAN bus termination resistor D-sub 9 pin male female connector
CAN bus termination resistor D-sub 9 pin male female connector
CAN bus termination resistor D-sub 9 pin male female connector
CAN bus termination resistor D-sub 9 pin male female connector
CAN bus termination resistor D-sub 9 pin male female connector
CAN bus termination resistor D-sub 9 pin male female connector 120 Ohm termination resistor CAN H and CAN L D-sub 9 pin 120 Ohm termination adapter CAN bus terminator
  • Model: 120 Ohm termination resistor CAN H and CAN L
  • Specification: D-sub 9 pin 120 Ohm termination adapter
  • Performance: CAN bus terminator
  • Category:
  • Category: CAN Bus Cable Adapter
  • Share This:        

CAN bus termination resistor D-sub 9 pin male female connector  

 

120 Ohm termination resistor CAN H and CAN L

 

D-sub 9 pin 120 Ohm termination adapter


 
CAN bus terminator 

 

D-sub 9 pin 120 Ohm termination adapter is a CAN adapter with a 9-pin male D-Sub connector at one end and a 9-pin female D-Sub socket at the other. 

 

Between CAN High (pin 7) and CAN Low (pin 2) there is a built-in 120 Ohm CAN terminating resistor.

 


CAN terminating resistor

 

Terminating resistors are used to eliminate signal reflections in communication cables. During communication, there are two reasons for signal reflections: impedance discontinuity and impedance mismatch

 

The impedance is discontinuous, and the signal suddenly encounters the cable at the end of the transmission line with little or no impedance, and the signal will cause reflections at this place.

 

The principle of this signal reflection is similar to the reflection of light.

 

 
Terminal resistance is divided into single resistance and double resistance. RS-485 bus terminal matching mostly adopts double resistance parallel terminal matching. If single resistance method is adopted, the parallel resistance value of the load terminal is equal to or similar to the characteristic impedance of the transmission line, so that the static current will be reduced. It will be very large, and it requires high current driving capability, and is rarely used.

 

Double-resistor parallel terminal matching is because the parallel value of the two resistors is equal to or similar to the characteristic impedance of the transmission line, and each resistance is larger than the characteristic impedance of the transmission line, so the current requirement is not high.

 

However, whether it is a single resistor or a double resistor is matched in parallel, it will always bring DC power consumption and reduce the bus load capacity.

 

Generally, the characteristic impedance of the 485 bus transmission line is 120 ohms, and two 120 ohm resistors are used as the terminal matching resistors of the 485 bus.

 

Since the parallel resistance of the 485 bus will lead to DC power consumption, it is generally recommended that the terminal resistance should not be connected when the transmission distance does not exceed 300 meters and the transmission rate is low. It is only considered when there is signal reflection in the transmission and the communication is unstable.  

 

CAN bus terminator D-sub 9 pin 120 Ohm termination adapter120 Ohm termination resistor CAN H and CAN LCAN bus termination resistor D-sub 9 pin male female connector

 

Copyright 2020  Premier Cable CO.,LTD   Suport:300.cn  Dongguan     粤ICP备2020142126号 

Copyright 2020  Premier Cable CO.,LTD   

Suport:300.cn  Dongguan

粤ICP备2020142126号